Hot tub heating guide
What Does It Really Cost To Heat A Hot Tub?
Almost all the electricity a hot tub uses goes on one job: putting back heat that escapes. Here's where that heat goes, how insulation and the weather change it, and how a heat pump makes the same heat for a fraction of the electricity. Then work out the figures for your own tub.
Skip to the calculator ↓Our example throughout: a 1,400 litre tub (6–7 seats) at 38°C with air-pocket insulation and a 3 kW heater, used three times a week for 30 minutes, refilled four times a year, in the Midlands, at 26.1p per kWh.
Where the heat goes
A hot tub is a large tank of water kept far warmer than the air around it, and heat always flows from warm to cold. Your heater's job is to replace it. In our example the yearly bill of £838 splits three ways:
The cover-on loss is the big one, because it never stops. Even with the lid shut, warmth leaks through the cabinet walls, the floor and the cover, 24 hours a day.
Taking the lid off is costly while it lasts. Open water loses heat quickly, and about 76% of it goes as evaporation: the steam you see on a cold evening is heat leaving the tub. A 30-minute soak on a January evening loses about 2.1 kWh, enough to drop the water about 1.3°C.
Refills cost about £13 each with the heater: 1,400 litres of mains water have to be warmed by more than 20°C in summer and over 30°C in winter.
Most of the bill is heat seeping out with the cover on, all day, every day. That's where better insulation and a more efficient heater pay off.
Insulation makes the biggest difference
How fast a tub loses heat with the cover on comes down to its insulation. We describe it as a heat-loss rate: how many watts escape for every degree the water is warmer than the air. A well-insulated tub loses about 43% less than a basic one:
| Insulation | A January day | Heater, per year |
|---|---|---|
| BasicCheaper tubs with thin panels or bare cabinets. | 11.4 kWh | £1,032 |
| Air-pocketA thermal wrap with an air gap between shell and cabinet. | 8.9 kWh | £838 |
| Full foamCabinet filled with open-cell foam around the shell. | 6.5 kWh | £644 |
The cover is part of the insulation too. A heavy, well-fitting cover with its seals intact keeps in far more heat than one that has soaked up water or no longer sits flat. Checking it costs nothing.
You can't see inside the cabinet, and makers rarely publish a figure. That's why the calculator lets you enter your actual usage instead: it then works out the heat-loss rate that matches your tub.
A fully foamed cabinet and a good cover can take hundreds of pounds a year off the bill before you change anything else.
Winter costs more, and so does the north
Heat loss depends on the gap between the water and the air. In the Midlands, the average January day is 4.2°C and the average July day 16.5°C, so holding 38°C water loses about 57% more heat in January than in July.
Where you live matters too. January averages 4.9°C in the south east of England and 2.9°C in the north of Scotland (Met Office averages for 1991–2020). The calculator uses the monthly averages for your region.
In the Midlands, holding temperature costs about 57% more in January than in July.
Every degree counts
Keeping the water at 36°C instead of 38°C cuts the heating bill by about 7%, roughly £63 a year in our example, because the gap to the outside air is smaller all year round.
If you're away for a few days, turning the temperature down saves more than it costs to heat back up.
Lower the temperature when you can, especially when you're away.
How a heat pump does the same job for less
A built-in heater turns electricity straight into heat: 1 kWh in, 1 kWh of heat out. A heat pump works like a fridge in reverse. It uses electricity to move heat that's already in the outdoor air into your water. That's why it can deliver several kWh of heat for each kWh it uses.
That ratio is called the COP (coefficient of performance). It depends on the weather: there's less heat to collect from cold air. Poolex rates the O'Spa 7kW at a COP of 3.6 at 15°C, 3.0 at 5°C and 2.65 at 0°C. Even on a freezing day it makes more than two and a half times the heat of a heater for the same electricity.
Two more things help. Cooler water is easier to heat, so warming a fresh refill is more efficient than holding the last few degrees. And an inverter heat pump such as the Ice Spa can slow down to match what the tub needs. When it's only holding temperature it runs gently, where it's most efficient: a COP of 4.2 at 15°C, against 3.7 flat out.
| Our example tub, heated by | Per year | Saving |
|---|---|---|
| 3 kW built-in heater | £838 | — |
| O'Spa 5kW heat pump | £294 | £544 · 65% |
| O'Spa 7kW heat pump | £258 | £580 · 69% |
| Ice Spa 7kW heat pump | £230 | £608 · 73% |
A heat pump cuts the cost of every kWh of heat, and insulation cuts how many you need. They work best together.
Getting a reliable estimate for your tub
The most accurate starting point is what your tub uses now. If it's on a smart plug, or your energy supplier's app shows a clear daily jump, note the figure and which month it's from. A January figure and a July figure from the same tub are very different, and the calculator matches yours to that month's weather.
A smart plug also measures the circulation pump, so take off about 1 kWh a day for that. No figure? Choose the insulation that best matches your tub, and adjust the sessions, temperature and tariff to suit how you use it.
A winter figure from a smart plug gives the most reliable result. Try it below.